 |
|
 |
Fixed Spreader Beam - Model 30
Ideal where head room is not limited. Adds stability to lift. Available with standard chain or wire rope rigging. Available with Adjust-A-Leg?rigging for off center load adjustment (minimum lifting capacity will be approximately 10?5% of beam rating). Wide range of additional sizes and capacities available. Designed and manufactured to ASME B30.20.
Rigging Options Available:
Option C: Chain top rigging from beam to crane hook.
Option W: Wire rope top rigging from beam to crane hook.
Option A: Adjust-A-Leg?sling top rigging for off center load adjustment.
|
|
 |
Adjustable Spreader Beam - Model 32
Ideal where head room is not limited. Adds stability to lift. Telescopic adjustable spread standard. Available with standard chain or wire rope rigging. Available with Adjust-A-Leg?rigging for off center load adjustment (minimum lifting capacity will be approximately 10?5% of beam rating). Wide range of additional sizes and capacities available. Designed and manufactured to ASME B30.20.
Specify top rigging options:
Option C: Chain top rigging from beam to crane hook.
Option W: Wire rope top rigging from beam to crane hook.
Option A: Adjust-A-Leg?sling top rigging for off center load adjustment.
Option HC: Hand crank for easier adjustment capabilities.
Not available on 12-20 ft. models.
|
|
 |
Low Headroom, Multiple Spread Lifting Beam - Model 20
Ideal where headroom is limited. Beams over 4 ft. have 3 spreads (3 ft. and 4 ft. beams have 2 spreads). Swivel hooks with hook latches standard. Wide range of sizes and capacities available. Designed and manufactured to ASME B30.20.
Three spreads to adjust to the load:
Outside spread
Middle spread (outside less 1 ft.)
Inside spread (outside less 2 ft.).
Product Options:
Option A: Extra Holes or Different Placement of Holes - Allows multiple hook positioning beyond standard 3 spreads. Specify number and spread(s) required.
Option B: Faspins - Faspins recommended if frequent hook position changes (spread) are required. For ease of positioning hooks with quick release. Specify number of faspins required.
Option C: Extra Hooks - Allows for multiple pick points. Specify number of hooks required.
Option D: Pin Type Bail - Lifting pin located between structural channel (hoist hook information must be supplied).
|
|
 |
Adjustable Bail Lifting Beam - Model 24
Ideal for off center loads by adjusting bail before lift. Adjustable spread options available. Swivel hooks with hook latches standard. Wide range of size and capacities available. Designed and manufactured to ASME B30.20.
Three spreads to adjust to the load:
Outside spread
Middle spread (outside less 1 ft.)
Inside spread (outside less 2 ft.).
Product Options:
Option A: Extra Holes - Allows for multiple hook positioning. Specify number and spread(s) required. Could increase headroom dimension, consult factory.
Option B: Faspins - For ease of positioning hooks with quick release. Specify number of faspins required.
Option C: Extra Hooks - Allows for multiple pick points. Specify number of hooks required.
Option D: Lower Headroom - Lifting pin located between structural channel (hoist hook information must be supplied).
|
|
 |
Three Point Lifting Beam - Model 27T
This low head room lifting beam has been designed to handle large loads requiring multiple pick points. This product can be designed to include options such as adjustable spread options, adjustable bail for off center load adjustment, and multiple overhead hoists. Designed and manufactured to ASME B30.20.
Rigging Options Available:
Option A: Multiple Hoists - Can utilize 2 hoists to increase lifting capacity and stability.
Option B: Adjustable Bail - Used when loadleveling capability is required along length of load.
Option C: Adjustable Spread - Required when loads are of varying length and adjustability is required in both directions.
|
|
 |
Four Point Lifting Beam - Model 27F
This low head room lifting beam has been designed to handle large loads requiring multiple pick points. This product can be designed to include options such as adjustable spread options, adjustable bail for off center load adjustment, and multiple overhead hoists. Designed and manufactured to ASME B30.20.
Rigging Options Available:
Option A: Multiple Hoists - Can utilize 2 or 4 hoists to increase lifting capacity and stability.
Option B: Adjustable Bail - Used when loadleveling capability is required along length of load.Wire rope top rigging from beam to crane hook.
Option C: Adjustable Spread - Required when loads are of varying length and adjustability is required in both directions. Adjust-A-Leg?sling top rigging for off center load adjustment.
|
|
 |
Heavy Duty "C" Hook - Model 82
Designed for heavy duty applications. High tensile alloy steel plate reduces physical size and weight. Counter balanced to hang level. Inside radius on hooks avoid coil edge contact.
Curved coil saddle is standard. Guide handles for ease of coil positioning. Handles a wide range of coil widths. Available with optional padding for additional coil protection. Designed and manufactured to ASME B30.20.
|
|
 |
Heavy Duty Sheet Lifter - Model 60
Versatile handling of bundles of sheets and other loads stacked horizontally. Low head room design minimizes head room required for lift. One man operation minimizes handling cost. Self-locking worm-gear leg drive system.
Sheet Lifter Specifications:
Easy adjustment for different sheet widths
Higher strength tubular construction
Extra wide rack and pinion leg drive
Designed for greater sheet width range
Grabshoes are 15% longer than standard duty
Hand wheel leg adjustment standard
Designed and manufactured to ASME B30.20
Product Options:
Code A: Motorized leg adjustment
Code B: Chain-wheel leg adjustment
Code C: Extended length hand wheel leg adjustment
Code D: End chains with plate hooks
|
|
 |
Vacuum Lifters
Hook suspensed vacuum lifters are designed for efficient one-person operation in lifts of semiporous and non-porous material. Vacuum units will not mark or scratch material surfaces or edges.
Standard units are available as air powered or electrical powered. Custom engineered units to your specifications are available. Separate vacuum lifter catalog detailing over 100 models available.
Two Categories of Vacuum Lifters:
Standard Inline Pad Units for Narrow Applications - 3 models available
Standard Multiple Crossarm Units for Wider Applications - 3 models available
|
|
